I-beams, also known as steel beams, are long strips of steel with an I-shaped cross-section. I-beams are divided into ordinary I-beams and light I-beams. They are sections of steel with an I-beam shape.
I-beams are mainly divided into common I-beams, light I-beams and wide flange I-beams. These are divided into wide, medium and narrow flange I-beams according to the flange to web height ratio. The first two are produced in sizes 10-60, i.e. with a corresponding height of 10 cm-60 cm. At the same height, light I-beams have narrow flanges, thin webs and light weights. The wide flange I-beam, also known as H-beam, has a section characterised by two parallel legs and no slope on the inside of the legs. It is an economic section steel and is rolled on a four-roller universal mill, so it is also known as a "universal I-beam". National standards have been formed for ordinary and light I-beams.

I-beams, also known as steel beams, are long strips of steel with an I-shaped cross-section. I-beams are divided into ordinary I-beams and light I-beams. They are sections of steel with an I-beam shape.
I-beams are mainly divided into common I-beams, light I-beams and wide flange I-beams. These are divided into wide, medium and narrow flange I-beams according to the flange to web height ratio. The first two are produced in sizes 10-60, i.e. with a corresponding height of 10 cm-60 cm. At the same height, light I-beams have narrow flanges, thin webs and light weights. The wide flange I-beam, also known as H-beam, has a section characterised by two parallel legs and no slope on the inside of the legs. It is an economic section steel and is rolled on a four-roller universal mill, so it is also known as a "universal I-beam". National standards have been formed for ordinary and light I-beams.

I-beams, also known as steel beams, are long strips of steel with an I-shaped cross-section. I-beams are divided into ordinary I-beams and light I-beams. They are sections of steel with an I-beam shape.
I-beams are mainly divided into common I-beams, light I-beams and wide flange I-beams. These are divided into wide, medium and narrow flange I-beams according to the flange to web height ratio. The first two are produced in sizes 10-60, i.e. with a corresponding height of 10 cm-60 cm. At the same height, light I-beams have narrow flanges, thin webs and light weights. The wide flange I-beam, also known as H-beam, has a section characterised by two parallel legs and no slope on the inside of the legs. It is an economic section steel and is rolled on a four-roller universal mill, so it is also known as a "universal I-beam". National standards have been formed for ordinary and light I-beams.

The C-shaped steel profile is automatically formed by the C-shaped steel forming machine. The C-shaped steel forming machine can automatically complete the forming process of the C-shaped steel according to the given C-shaped steel size. C-shaped steel is widely used in purlins and wall beams of steel structure buildings, and can also be combined into lightweight roof trusses, brackets and other building components. In addition, it can also be used for columns, beams and arms in mechanical light industry manufacturing.

Z-shaped steel profile is a common cold-formed thin-walled steel, the thickness is generally between 1.6-3.0mm, and the section height is mostly between 120-350mm. The processing material is hot-rolled (painted), galvanized. The processing standard is implemented according to GB50018-2002. Z-section steel is usually used in large-scale steel structure workshops. The processing length and holes are produced according to the processing requirements. Ancillary products: color steel tile; rock wool sandwich panel; floor deck, etc.

Z-shaped steel profile is a common cold-formed thin-walled steel, the thickness is generally between 1.6-3.0mm, and the section height is mostly between 120-350mm. The processing material is hot-rolled (painted), galvanized. The processing standard is implemented according to GB50018-2002. Z-section steel is usually used in large-scale steel structure workshops. The processing length and holes are produced according to the processing requirements. Ancillary products: color steel tile; rock wool sandwich panel; floor deck, etc.

Z-shaped steel profile is a common cold-formed thin-walled steel, the thickness is generally between 1.6-3.0mm, and the section height is mostly between 120-350mm. The processing material is hot-rolled (painted), galvanized. The processing standard is implemented according to GB50018-2002. Z-section steel is usually used in large-scale steel structure workshops. The processing length and holes are produced according to the processing requirements. Ancillary products: color steel tile; rock wool sandwich panel; floor deck, etc.

A615 grade 40 steel adds the most benefit when building materials must hold concrete in compression. Strength is one of the differentiators for these two rebar grades. The minimum tensile strength for A615 grade 40 steel is 70.05 ksi. It has a minimum yield strength of 40 ksi.

Channel section steel is kind of carbon structural steel, for its high strength and good weld bility, it can be used in construction and automobile manufacture. We also provide flat bar plate, flat bulb steel, angle steel and other hot rolled steel. 
Hot-dip galvanized channel steel can be divided into hot-dip galvanized channel steel and hot-blown galvanized channel steel according to different galvanizing processes. A zinc layer is attached to the surface of the component, so as to achieve the purpose of anti-corrosion.
The main method of galvanizing the surface of channel steel is hot-dip galvanizing. Hot-dip galvanizing is developed from the older hot-dip galvanizing method, which has a history of 170 years since the application of hot-dip galvanizing to industry in France in 1836. However, in the past 30 years, with the rapid development of cold-rolled strip, the hot-dip galvanizing industry has developed on a large scale.

Among various coating methods for protecting steel substrates, hot-dip galvanizing is a very good one. It is in the liquid state of zinc, after quite complex physical and chemical action, not only a thick pure zinc layer is plated on the steel, but also a zinc-iron alloy layer is formed. This kind of plating method not only has the corrosion resistance characteristics of electro-galvanizing, but also has a zinc-iron alloy layer. It also has strong corrosion resistance unmatched by electro-galvanizing. Therefore, this plating method is especially suitable for strong corrosive environments such as various strong acids and alkali mists.

Channel section steel is kind of carbon structural steel, for its high strength and good weld bility, it can be used in construction and automobile manufacture. We also provide flat bar plate, flat bulb steel, angle steel and other hot rolled steel. 
Hot-dip galvanized channel steel can be divided into hot-dip galvanized channel steel and hot-blown galvanized channel steel according to different galvanizing processes. A zinc layer is attached to the surface of the component, so as to achieve the purpose of anti-corrosion.
The main method of galvanizing the surface of channel steel is hot-dip galvanizing. Hot-dip galvanizing is developed from the older hot-dip galvanizing method, which has a history of 170 years since the application of hot-dip galvanizing to industry in France in 1836. However, in the past 30 years, with the rapid development of cold-rolled strip, the hot-dip galvanizing industry has developed on a large scale.

Among various coating methods for protecting steel substrates, hot-dip galvanizing is a very good one. It is in the liquid state of zinc, after quite complex physical and chemical action, not only a thick pure zinc layer is plated on the steel, but also a zinc-iron alloy layer is formed. This kind of plating method not only has the corrosion resistance characteristics of electro-galvanizing, but also has a zinc-iron alloy layer. It also has strong corrosion resistance unmatched by electro-galvanizing. Therefore, this plating method is especially suitable for strong corrosive environments such as various strong acids and alkali mists.

Channel section steel is kind of carbon structural steel, for its high strength and good weld bility, it can be used in construction and automobile manufacture. We also provide flat bar plate, flat bulb steel, angle steel and other hot rolled steel. 
Hot-dip galvanized channel steel can be divided into hot-dip galvanized channel steel and hot-blown galvanized channel steel according to different galvanizing processes. A zinc layer is attached to the surface of the component, so as to achieve the purpose of anti-corrosion.
The main method of galvanizing the surface of channel steel is hot-dip galvanizing. Hot-dip galvanizing is developed from the older hot-dip galvanizing method, which has a history of 170 years since the application of hot-dip galvanizing to industry in France in 1836. However, in the past 30 years, with the rapid development of cold-rolled strip, the hot-dip galvanizing industry has developed on a large scale.

Among various coating methods for protecting steel substrates, hot-dip galvanizing is a very good one. It is in the liquid state of zinc, after quite complex physical and chemical action, not only a thick pure zinc layer is plated on the steel, but also a zinc-iron alloy layer is formed. This kind of plating method not only has the corrosion resistance characteristics of electro-galvanizing, but also has a zinc-iron alloy layer. It also has strong corrosion resistance unmatched by electro-galvanizing. Therefore, this plating method is especially suitable for strong corrosive environments such as various strong acids and alkali mists.

ASTM A615 is a deformed steel standard categorized under American standards. These are generally available in diameter between 9.5 mm and 43 mm, and length between 6 m and 12 m. Generally, the steel bars that fall under this standard are under deformed or plain carbon steel.